您好,欢迎进入深圳市羽杰科技有限公司官网!
183-0000-2010

联系我们

深圳市羽杰科技有限公司
联系人:王生
电话:183-0000-2010
地址:深圳市龙岗区平湖华南城M20栋 在线咨询

环保脱模剂

铝模板脱模剂|建筑铝模板脱模剂|铝模板水性脱模剂

清除铝模板表面铝糠、灰尘及其他固体脏物;清洁铝模板表面的工业油污、乳化脏物;调整乳液的粘度到适合的范围
咨询热线:183-0000-2010

产品介绍

铝模板脱模剂

Aluminium template release agent

55a6060330186.jpg

性能指标:

Performance indicators:

外观: 铝灰色

Appearance: Aluminum gray

适用范围: 适用于铝合金

Scope of application: Suitable for aluminium alloy

成分: 改性高分子聚合物,水

Ingredients: modified polymer, water

漆膜硬度: ≧1H

Film Hardness: > 1H

涂刷面积: 6-8平方米/千克

Brushing area: 6-8 m2/kg

干燥时间(25℃,80%) 表干: 10-20分钟

Drying time (25 C, 80%) surface drying: 10-20 minutes

实干: 自干72小时

Practical work: self work for 72 hours

施工方法:直接使用,可用滚筒涂刷;静电喷涂

Construction method: direct use, can be brushed by drum; electrostatic spraying

方法一:涂料滚筒

Method 1: Coating drum

1.清除铝模板表面铝糠、灰尘及其他固体脏物;

1. Remove aluminium chaff, dust and other solid dirt on the surface of aluminium template;

2.清洁铝模板表面的工业油污、乳化脏物;

2. Clean industrial oil and emulsified dirt on the surface of aluminium template;

3.采用涂料滚筒涂刷时要确保涂刷均匀、到位(以涂料滚筒来回滚动模板两次,漆膜厚度约为15-20微米为准);

3. Make sure that the coating is uniform and in place when using the coating drum (the thickness of the coating film is about 15-20 microns when the coating drum rolls back and forth twice);

4.漆膜表干后即可对模板进行堆放(涂刷保模剂5-10分钟左右漆膜就可以达到表干状态)

4. When the surface of the paint film is dry, the template can be stacked (the film can reach the surface dry state by brushing the mould-keeping agent for about 5-10 minutes).

方法二:传统式空气喷涂

Method 2: Traditional air spraying

1.清除铝模板表面铝糠、灰尘及其他固体脏物;

1. Remove aluminium chaff, dust and other solid dirt on the surface of aluminium template;

2.清洁铝模板表面的工业油污、乳化脏物;

2. Clean industrial oil and emulsified dirt on the surface of aluminium template;

3.调整乳液的粘度到适合的范围

3. adjust the viscosity of the emulsion to the appropriate range.

4.将气量,气压,喷漆量调整到最佳状态对铝模板进行涂刷;

4. Adjust the air volume, air pressure and paint amount to the optimum condition to paint the aluminum template.

5.喷枪与工件的距离以20-30CM为宜,来回喷涂一次,漆膜厚度为15-25微米为最佳状态

5. The distance between the spray gun and the workpiece should be 20-30CM. The best condition is to spray back and forth once, and the film thickness is 15-25micron.

本文标题:铝模板脱模剂|建筑铝模板脱模剂|铝模板水性脱模剂 原文链接地址:http://www.fangxiuoil.com/show.asp?id=41

标签:全部
网友评论

管理员

该内容暂无评论

中国网友
183-0000-2010